room correction

Hi everyone I've always had a doubt about the two functions of the title and I decided to ask those who know more than me to dispel any doubts and gain some certainty. So, I choose an RF profile or an equalization (GEQ or PEQ) and activate the profile or equalization. What happens if I close...

UMIK-1 in the house, I downloaded the calibration files and used the iPad with the microphone pointed directly at the speakers sitting on the coffee table using the supplied tripod closer to speaker level than ear level. used 30hz-500hz, crossover 90hz, B&K So far I found myself turning the sub...

I've been listening to my Amp with Roomfit 20Hz-600Hz, B&K target, individual channel, cut only mode and it sounds fine. I thought I would try the flat target instead of B&K and the results look almost exactly the same to me. Anyone else tried the comparison. I have always seen and heard a...

I've run RoomFit in two rooms now and it's a clear improvement in sound quality over using Room Correction for me. I've played with it a bit and since documentation is light on this currently thought it might be useful to post how I have used it. Here's my setup for ref: Office: Q Acoustic...

tl;dr: I'm feeding a miniDSP Flex HT via Toslink for all processing, so the WiiM's DAC and analog outs won't be used. Is there any reason (better clocking, cleaner digital signal, etc.) that the Pro Plus or Ultra would perform better as a pure transport than the standard WiiM Pro in a high-end...

What is the correct approach to compensate for gain boosts in RoomFit/(P)EQ in order to avoid clipping? I’ve read somewhere that the volume limit feature can be used for this. Would that have the same affect as setting negative pre gain in the input options, but for all inputs? If the volume...

The room EQ in my av processor (Tonewinner AT-300) is lousy (boosts +12) the room EQ in the Wiim is much better, with more adjustability. So instead of using the Tonewinner EQ I've copied what the Wiim app PEQ has calculated into the AT-300 EQ preset- so for every "movie" source it will use...

I tooks some measurements using REW to see what exactly each EQ filter is doing in the WIIM Ultra (very likely also applies to the other WIIM devices with PEQ): https://drive.google.com/drive/folders/1dn8LXOGKAgZzBwcPt8xlftjE9Lp3DDK7 (google drive link, let me know if it doesn't work) The "App"...

Android 16 phone #1 Top Concern: Room Correction -> Audio Check/Natural Sound - no sound audible. Optical in, Speaker out works perfectly. Audio track stored on phone plays perfectly through speaker out. But, Browse -> Amazon Music -> triangle play button only shows moving waveform -> then...

The punchline here is if I should further “manually” tweak my RC PEQ and if so what bumps (up/down) would you do? For starters, after some trial and error with my active Definitive Technology SuperCube II subwoofer I found that setting volume at about 40% on the sub and phase from 0 degrees to...

I have run the room correction routine for my Wiim Pro and prefer casting Quobuz from the app rather than through the Wiim app. If I do this, will the room correction EQ be applied or is this only done when accessing Quobuz directly from the Wiim app?

Hi, This support article claims (in the section 'How Room Correction and EQ Work Together' at the bottom) that it is possible to use EQ and room correction together. But it doesn't seem to be the case, because what Room Correction does is it creates a preset for Parametric Equalizer and applies...

Is anyone able to explain how the WiiM's deal with adjustments in the digital domain (volume, room correction, EQ)? That is, do they leave the original file in tact and send it to the DAC with a sort of xml or sidecar file attached with instructions of how to adjust the original file or does it...

This is a bit confusing what are the two settings main gain and min gain?

Hi, I've got a setup with an Amp, a pair of bookshelf speakers and a powered sub. Currently, I have the crossover frequency set to 100 Hz. When running room correction, should I set the frequency range to start at 20 Hz, or at the crossover frequency of 100 Hz? Initially I thought to run it from...

I can't seem to get Room Correction to work. I'm using the app on an android. As soon as I click 'Next' a 'failed' message appears. I've rebooted both the device and my phone, checked microphone permissions and restarted router. Both phone and device are on the same network. Any ideas? #Room...

Hello there, I have some questions about my setup: I use the Wiim Ultra inbetween a Power Amp (Pro-Ject DS2 Amp Box) and an AVR (Marantz Cinema 70s) as a Preamp (Connection via RCA from the Marantz Front Preouts into the Line In of the Wiim Ultra, Volume Set to 100%). I use Audyssey via the...

Howdy! Recently swapped my Polk XT15's for the Monitor Audio Bronze 100's, got them for a great price. These are paired up with a Polk PSW10 10" sub, that's at 60% volume, and on my Wiim Amp set to -3db's, some of the bass is coming from the MA 100's. The Room Correction is giving me rather...

I am very disappointed with the Wiim Ultra RC, and also cast my vote for adding DIRAC compatibility. Initially, I used the Wiim's RC because I thought it would improve the sound, but after reading the manual I realized that it was significantly altering the sound so I turned it off. After...

Hi, I hope someone has a solution for me. I was trying some new room corrections today because I changed the room around a little bit with a new subwoofer and new placement for speakers. But now the Room Correction no longer works. It's stuck in the Welcome to Room Correction (elevate your...