wiim amp

After my reboot Of Wiim AMP, Spotify connect now recognize two WiiM AMP devices. I marked the one that doesn’t work. Does anyone know How to remove it from the recognized devices? I don’t have any option for it (like three dots on the right that I have for valid device).

My Wiim Amp cuts subwoofer out abruptly, sometimes it works fine, sometimes creates very low popping noise, sometimes kicks back in. I turn the sub-out off and on from the app, it starts working normal and cuts off again. Non repeatable consistently. Very annoying. Switched the sub to see if...

Hey all, I'm hoping maybe we can crowdsource some information. I recently investigated some poor quality audio in my setup (Apple TV 4K -> TV -> Wiim Amp Pro), and found my TV to be the culprit. I was able to verify that it was, at a minimum, resampling the input, and possibly performing...

Greetings, all! I'm considering using a WiiM Amp for an outdoor patio zone that will have 6 x 8 ohm satellite speakers (similar to Sonance MAG system). If I run 3 in a left channel (in parallel) and 3 in a right channel (in parallel), it will end up presenting with a 2.67ohm load to the amp on...

Hello all! My WiiM AMP is not powered on. Yesterday morning it worked fine, but 2 hours later when I was powering on my TV there was no sound from the wiim (the orange diode light all the time). I was trying to restart the device with the remote control and plug it off, but it hasn't helped...

My Wiim Amp has been spontaneously and randomly rebooting. I have disconnected the power cord and after a few minutes reconnected it. This is not a permanant solution. Question 1: Does a power off/on cycle have exactly the same effect as a Reboot using the WiiM Home App? Question 2: Does a...

Apologies if the answers are else where, but I am struggling to find exactly what I need so am hoping I can ask more knowledgeable folks than myself. I just moved into a new place with in-ceiling speakers throughout the house. For the most part I think I want to use the system for streaming...

So I experienced a problem where my subwoofer would not produce any sound. I tried any possible solution like switching L and R inputs in my subwoofer, cranking the volume up both in the wiim home app and the subwoofer, rebooting and factory resetting the wiim amp, and switching to a different...

I've been using a WiiM Pro connected to an NAD 338 via Toslink. I'm happy with the sound, but curious if things might improve if I remove the middle man and just get a WiiM Amp. Any experience with this?

I have a problem with my setup. Many TV channels only output sound via Dolby Digital via Bitstream. There is no sound coming from the speakers on my WIIM AMP. When deciding to buy WIIM AMP or WIIM AMP Pro, I compared all the technical data from the official sources. It was not obvious that there...

Sorry for the long-winded post but after hours of research I thought I’d just ask. I’m completely new to audio systems but have learned a bit and just wanted to get some expert opinions. I’m having a free-standing aluminum covered pergola built that will have wifi and power that is right next to...

Hi all. One for the collective hive-mind of the great-and-good of the WiiM community Found this thread where the OP seems to perfectly describe the issue I'm also having: https://forum.wiimhome.com/threads/show-a-single-entry-for-compilation-albums-in-app-usb-media-library-album-view.5729/...

I mainly use the Wiim Amp with my TV. Unfortunately, the television sound is transmitted too quietly via the HDMI ARC port. The sound source is a SAT receiver. If I set the output to “Bitstream”, the sound is great, but then I have no sound at all on some channels (RTL, Vox). If I set the output...

Hi all, I was wondering if I can connect the Project CD Box E which has an coaxial output to the Wiim Amp which has an optical input using this cable...

I have a few WiiM Amps and noticed that there are some differences between them. Here are a few of the differences when I run getStatusEx: "firmware": "Linkplay.5.0.704664", "project": "WiiM_AMP", "Release": "20250115", "PCB_version": "6", "wmrm_version": "4.3"...

Hello, Can someone tell me how and where I can assign the buttons of the remote control (1-4) and what these buttons should be for? Where can I find a description of this? Thank you and VG

Hey everyone! I have 2 - WiiM Amps pushing some restored Cerwin Vegas. I would like to split the Toslink /optical out from my tv and feed both WiiM Amps the same signal. Has anyone run into an issue with this? I tried to run Toslink Optical input to one of the WiiM Amps and then group the...

Hi I have a Wiim Amp and have today received a Panasonic UB820 4k Blu-ray player. The UB820 has dual hdmi outputs one for video to my projector and one for audio only which I plugged into the hdmi input on the Wiim amp, but of course as with everything I always assume will work straight away...

I just got my Wiim Amp and love it. I would love to see an ability to navigate through radio presets added to the list of favorite radio stations using the remote navigation buttons, the skip back and forward buttons to scroll through the presets. Currently we always have to use phone to access...

MacOS, iOS, iPad OS and old versions of tv OS can assign wired speakers connected to Wiim devices as AirPlay Speakers. The WiiM device is not involved with AirPlay whatsoever. It processes the data stream as exactly as it proccess TOSLINK digital input from all non-Apple device. The solution...