room correction

Are there any videos around that go through sub sync, roomfit, room correction, EQ, etc. tutorials with a preferred order of operations? I feel like I have my system (using Wiim Ultra) sounding pretty good, but I have a feeling I may be missing out on some tips and tricks. The order of...

Another room fit,correction question At what volume should you do room fit,correction ? At low levels the bass might not be to loud,noticeable and at high level the frequency responce can change alot with a brighter sound or more boomy bass or sharpness in the midrange

Today I accidentally noticed several improvements to RoomFit Moving Mic Measurement (MMM) beta feature which seem to have been added silently at some point: There's a screen now explaining how to perform MMM It is now possible to use "Individual Channel RoomFit" mode while MMM is enabled: If...

Do you also need to signiificantly increase volume level when doing correction through USB Out? I have to turn up the volume more than twice to get a similar sound level to when listening to music. However, when I do auto SYNC between the speakers and the subwoofer, this problem does not...

I don't understand why I see large dips (~around the 3-4k) in the verification 'actual' response? I apply correction up to 400hz so i thought the before and after would be similar above that freq. I see them in both individual and stereo measurements. I tried q3 and q10, crossovers...

Hi! I have been playing with room correction for a while, but IF set correct, the results sounds dull, lifeless to me. Anyone have experience with the opposite of room correction, i e. Acoustic threatment? Btw, I love to use the in-app Equilizer for the Wiim Ultra. Little more bass, little...

Did lots of reading, partially understand so wanted some input on results. I am using a Umik-1 just taking a single measurement on each channel. Speakers are Wharfedale 12.2's which can get down to 50's per specs (roll off sooner per the graphs). I started with 20-500 and ended up narrowing down...

I would like it if wiim amps could have an update,firmware,home app (i own a wiim amp pro) that would make it aut adjust crossover for a sub and front speaker and of course level,room correction at the same time when using roomfit/room correction That way you have an option of letting the amp...

Hello everyone, I've been experimenting with RoomFit to correct the low-frequency issues in my room using my KEF LSX II speakers (with their internal EQ disabled) connected to a WiiM Ultra via optical cable. I don't use sub. I ran three Individual Channel RoomFit sessions and would appreciate...

Hi, if this post is stupid, then I'm sorry. But I don't know how good RoomFit curve should look like I tried to compare mine to others but it is hard to find many examples. So my idea is to open a thread where everybody can share theirs curve screen shot so others can comment on it. I have...

I was hope to correct some frequencies with roomfit. The iPad 11 was okey to find a sweet spot, but my new iPhone air was totally disaster with all bass was gone -10 in the low bass frequencies. I think a microphone can handle this much better like Sound Id (sonarworks).

Hello all: When I run RoomFit with the phone mic (Samsung) it runs fine. However, when I run it with the Dayton mic I get an error that the background level is too high (although there is no background noise. The mic is properly recognized and the calibration file was imported. I tried it...

Is it possible to make a custom room fit target curve or download additional filters Can i have 2 or 3 profiles like having flat,harman and B&K roomcorretion profiles i can switch between How big is the difference between B&K and Harman

Hi, I'm not very busy today and the temperature outside is over 39°C, so I decided to conduct the experiment inside the air-conditioned house 😄 A slightly bizarre RoomFit test. [Overview] Perform a RoomFit on each of the two WiiM devices in two different rooms and compare the results of Room...

Is it yet possible to assign a set number of PEQ bands to room correction, let's say seven or eight, and keep the other two or three separate for your own use (specific speaker correction)?

Hi all. I'm a silent reader in this forum and I'm learning a lot especially from @dominikz and @harkpabst. I just bought a Wiim Amp Ultra and I would like to use Room Fit for my budget Polk XT20 speaker and SVS SB-1000 Pro subwoofer. I would like to have your advice if my plan is in the right...

Finally finally got my Dayton Audio mic and the calibration file downloaded and incorporated into the Wiim app. The sound is mahvelous! The strangeness is while calibrating the speakers, the screen asks "Did you hear deep bass?" Well, no. All we heard was something like running water while...

I may have discovered a long-requested feature: 20 filters to use with Room Fit. Here's what I did: 1) I performed a Room Correction using House Curve, which allows up to 20 filters using all 20 of them. 2) Once I had the correction for the 20 frequencies, I manually copied 10 values into Room...

With the excellent RoomFit levelling out the room modes, and now the EQ being able to superimpose the desired sound signature I think the Wiim Ultra is an amazing sounding device. The problem is, these settings are still active when I select headphone output. This makes them sound off as my ears...

Welp, I keep up with the firmware updates pretty regularly. Upon my most recent update, my room correction profiles (all but 2-3) were all wiped out. I had a feeling that something like this would eventually happen, so lucky for me, I took screenshots of my favorite room correction settings and...