roomfit

Hallo Hello My "problem" is that the settings are not displayed synchronously on all devices (iPad, Samsung smartphone, etc.). left Smartphone / right iPad

Hello everyone, I've been experimenting with RoomFit to correct the low-frequency issues in my room using my KEF LSX II speakers (with their internal EQ disabled) connected to a WiiM Ultra via optical cable. I don't use sub. I ran three Individual Channel RoomFit sessions and would appreciate...

My VU meters stopped working so I did a factory reset and it restored them. 😊 Now when I go to do a roomfit the profiles like Harmon, B&K etc are no longer there. Checked to make sure I had the latest update and I do. Any ideas folks? Thanks very much

I’m new to WIIM products and I’m trying to run RoomFit but need some clarification when it comes to my setup as I’ve seen contradictory information and want to make sure I do it correctly. I have the WIIM Pro hooked to my powered speakers via the optical out and a powered subwoofer connected to...

Hi, if this post is stupid, then I'm sorry. But I don't know how good RoomFit curve should look like I tried to compare mine to others but it is hard to find many examples. So my idea is to open a thread where everybody can share theirs curve screen shot so others can comment on it. I have...

After setting up the amp in my bedroom system and studying the documentation I discovered that the Wiim Amp Pro's bass management can be set up as a 4th order Linkwitz-Riley crossover. I have a pair of Quad ESL-63 speakers in my living room that are famous for incredible sound quality, but...

I was hope to correct some frequencies with roomfit. The iPad 11 was okey to find a sweet spot, but my new iPhone air was totally disaster with all bass was gone -10 in the low bass frequencies. I think a microphone can handle this much better like Sound Id (sonarworks).

Hello! When doing room fit (with microphone on Pixel 8 PRO) it always shows a very strange curve when checking the results. What's most prominent is the lack of base according to the curve, but it's not The case when actually listening. I've tried with an IPhone as well, but it's The same...

Hi, Equalizer stop responding. This is second time. I was using it. What I did or why? I rebooted now it's the same. EQ and roomfit doesn't change/control the sound.

Hello all: When I run RoomFit with the phone mic (Samsung) it runs fine. However, when I run it with the Dayton mic I get an error that the background level is too high (although there is no background noise. The mic is properly recognized and the calibration file was imported. I tried it...

I have been experimenting with RoomFit and have never really obtained a good sound unless I tweaked EQ afterwards. So my calibration process has been: - run a sub sync first - then run a Roomfit correction (I use BK curve) - fine tune EQ/PEQ to your liking or to get the measured sound curve as...

Sorry if this has been asked/answered before, but I couldn’t find it here. My setup: Roon Server on Windows 11 (Tidal and local files on Synology NAS) > 5Ghz Wifi (FritzBox 7530) > Wiim Amp Ultra Question: Are my RoomFit settings being used if I play music via the Roon app or are they ignored...

Is it possible to get the option to default roomfit on or off in presets - apparently the ultra has this feature (as announced in a recent firmware update) - but not my pro plus and my WiiM amp. It is annoying to go in and disable and enable it every time I use headphones! I basically just...

I ask for Harman, it gives me this (I used red to mark the resulting curve based on its automatic correction algorithm) when setting correction range up to 250Hz: Hilariously bad. This worked better months ago the last time I tried it. Whatever, “enhancements,” have been made seem to have...

I love my Ultra and the RoomFit. My right speaker is in the corner and my left is free standing, both 15 cm from the back wall. Here's the problem: The vocal is always a little to the left, not in the center. Is there a way to adjust this?

I used RoomFit for the first time and the process was pretty easy. But I have a question about how to know if it is being used or not. In the RoomFit Dialog it says RoomFit is on and I select the correct profile to use. However, when I go to the playing now screen, the equalizer icon on the...

Is it possible to make a custom room fit target curve or download additional filters Can i have 2 or 3 profiles like having flat,harman and B&K roomcorretion profiles i can switch between How big is the difference between B&K and Harman

Hi, I'm not very busy today and the temperature outside is over 39°C, so I decided to conduct the experiment inside the air-conditioned house 😄 A slightly bizarre RoomFit test. [Overview] Perform a RoomFit on each of the two WiiM devices in two different rooms and compare the results of Room...

Is it yet possible to assign a set number of PEQ bands to room correction, let's say seven or eight, and keep the other two or three separate for your own use (specific speaker correction)?

New to RoomFit. Once you have tested your room and saved a profile is it just a matter of ensuring RoonFit is on - the profile is selected and the Parametric EQ is on as well? Thank you! ~Peter